Can You Get Rid of Rust on a Car
How to Repair Rust on a Car
As long as vehicle body panels are made from steel, they're going to rust.
Introduction
Sooner or later, rust on cars is inevitable. However, if you deal with rust early, you can stop it from spreading and squeeze a few extra years out of your vehicle.
Rust repair isn't hard, but it is time-consuming (mostly waiting for primer and paint to dry between steps). Plan to spend about $100 on supplies like sandpaper, primer, masking tape and poly sheeting, a tack rag, polishing compound and touch-up paint and clear coat. Choose a calm, overcast day and block out the full day to fix the most common rust spots on the hood and doors.
ⓘ
Project step-by-step (9)
Step 1
Go Shopping for Supplies
- First, find the car manufacturer's paint code.
- Note: The paint code can be in a variety of places on the body, in the engine compartment or trunk, or other places. Use either of these online resources to find instructions on how to locate your paint code: automotivetouchup.com or duplicolor.com.
- Buy automotive touch-up paint in pints and quarts to use in a spray gun, in aerosol cans, or in roller ball applicators.
- Pro tip: Even if you know how to use a spray gun, mixing automotive paint with a reducer to match the temperature and humidity conditions can be mighty tricky. We don't recommend it. Instead, buy aerosol cans for larger repairs and rollerball applicators to fix scratches.
- Note: Most late-model vehicles were painted with base coat/clear coat paint. The base coat contains just the pigment and binding resins-the clear coat is just the gloss.
- Buy equal amounts of both base coat and clear coat.
- You'll also need an epoxy self-etching primer to bite into the bare metal and a lacquer primer to hold the paint.
- Buy 40-, 600- and 1,000-grit sandpaper, a sanding block, grease and wax remover, poly sheeting, painter's tape, a tack rag and a microfiber cloth.
Step 2
Mask Off the Repair Area
- Tape the leading edge of poly sheeting a few feet away from the repair so you'll have room to blend the touch-up paint into the good areas.
Sign Up For Our Newsletter
Complete DIY projects like a pro! Sign up for our newsletter!
Do It Right, Do It Yourself!
Step 3
Remove the Rust
- Crack off any blistered pint with a scraper.
- Sand through the rust spots down to the bare metal, using 40-grit sandpaper.
- Enlarge the sanded area so you'll have space to feather the edges.
- Switch to 120-grit sandpaper to feather the edges of the repair area.
- Complete the feathering with 220 grit.
- Use a tack rag to remove particles from the unmasked area.
Step 4
Clean with Detergent
- If the rust has created pits in the metal, you can fill them now with body filler or wait until the epoxy primer dries and apply multiple coats of filler primer.
- Clean the entire unmasked area with a grease-cutting dishwashing detergent, followed by clean rinse water.
- Let it dry.
- Wipe the area with a lint-free cloth to remove any remaining dust or lint.
- Apply the paint manufacturer's prep solvent.
Step 5
Apply Epoxy Primer, Then Filler Primer
- Spray the filler primer in heavier coats to cover the entire repair area.
- Move the can away from the surface slightly and blend it into the surrounding painted area.
- Pro tip: Self-etching epoxy primer provides a strong bond to bare metal, so use it as your first coat.
- Spray two to three medium coats, allowing the recommended wait time listed on the label (usually 15 minutes) between coats.
- Wait a full hour for the epoxy to dry to the touch (longer if it's humid outside).
Step 6
Sand the Primer
- Starting with wet 600-grit sandpaper, smooth the primer and feather the edges.
- Switch to wet 1,000-grit sandpaper to final-sand the entire repair, including the blended areas.
- Wash with clear water and let dry.
- Wipe the dried epoxy primer with a lint-free cloth.
- Apply two to three heavier coats of lacquer filler primer, allowing drying time between each coat.
- Let the lacquer primer dry until it's dry to the touch—at least one hour—before sanding.
- Sand drips and sags with 320-grit sandpaper.
- Then final-sand the entire repair area.
Step 7
Apply the Colored Base Coat
- Holding the spray can about 12 in. away from the surface, spray the repaired area.
- Start at the bottom of the repair and apply the color coat in left-to-right rows, overlapping each pass by about one-third.
- Build the color slowly into the repair and surrounding areas in two to three coats.
- Allow about 10 to 15 minutes between coats.
- Allow the base coat to dry, until it's dry to the touch, at least 60 minutes.
- Pro tip: Don't sand the base coat (especially metallic colors) unless you've created sags. In that case, sand lightly and then respray the touched-up areas.
Step 8
Spray on the Clear Coat
- Apply several coats of clear coat, allowing the recommended drying time between coats.
- Gradually work the clear coat into the surrounding painted areas to achieve a smooth blend line.
- Note: This is the hardest part because all clear coats run easily and that will ruin the look of your paint job. If you create a run in the clear coat, you'll have to let it dry for at least 48 hours before attempting to fix it with fine-grit sandpaper and polishing compound. Then you'll have to respray the sanded area. So practice spraying on a scrap piece of cardboard to get a feel for the nozzle and the speed of application.
- Let the clear coat dry for several hours before driving the vehicle and at least 48 hours before buffing.
Step 9
Buff the Repair
- Using an old cotton T-shirt or microfiber cloth and buffing compound, hand-buff the repaired area.
- Pro tip: Don't use a polishing machine for this step. Wait at least 30 days before waxing.
Can You Get Rid of Rust on a Car
Source: https://www.familyhandyman.com/project/how-to-repair-rust-on-a-car/